The most widely used of all optoelectronic devices is the simple LED (light emitting diode), which emits a fairly narrow bandwidth of visible (usually red, orange, yellow, or green) or invisible (infrared) light when its internal diode junction is stimulated by a forward electric current.
LEDs have typical power-to-light energy conversion efficiencies some 10 to 100 times greater than a simple tungsten filament lamp and have very fast response times (less than 0.1µS, compared to 10s or 100s of milliseconds for a tungsten lamp), and are thus widely used as visual indicators and as simple ‘flashing light’ units. A variety of such circuits are shown in this article.
LED BASICS
INTRODUCTION
Figure 1 shows the standard symbol that is used to represent an LED in this article, together with its basic anode (a) and cathode (k) terminal notations.
FIGURE 1. Standard LED symbol, together with its terminal notations.
LEDs are pn junction diodes, usually made from gallium arsenide (GaAs) or aluminum-gallium arsenide (AlGaAs) types of semiconductor materials, and emit light when stimulated by a forward current.
Roughly 2V are developed across them when passing a useful forward current; Figure 2 lists the typical forward volt drops (Vf) of different colored standard 5mm diameter LEDs at forward currents of 20mA.
COLOR | Red | Orange | Yellow | Green | Blue |
---|---|---|---|---|---|
Vf (typical) | 2V | 2V | 2.1V | 2.2V | 3.3V |
FIGURE 2. Typical forward voltage values of standard LEDs at a current-limited value of 20mA.
If an LED is reverse-biased, it starts to pass significant current at a fairly low voltage value (typically 3V to 5V) and eventually avalanches (zeners) at higher voltages.
LEDs are available in a variety of styles, the most popular being the ‘round’ type that has the basic shape shown in Figure 3 and which is readily available in standard diameter sizes of 3mm, 5mm, 8mm, or 10mm. Round LEDs use a clear or colored plastic case with a lens molded into its dome, and are designed to be viewed end-on, looking towards the dome, as indicated in the diagram.
FIGURE 3. Typical physical details of ‘round’ LEDs and methods of recognizing their polarity.
The LED case has a polarity-identifying ‘flat’ molded into the side of its base adjacent to the cathode lead, which is usually shorter than the anode lead when untrimmed. Special fittings are readily available for fixing most sizes of LED to front panels, etc.
One important but confusingly-named LED parameter is its ‘viewing angle,’ at the extremes of which the LED’s optical output intensity falls to half of its maximum axial value. Some LEDs give a diffused output in which the light intensity falls off gradually beyond the viewing angle and is thus clearly discernable over a wide angular range; others (particularly ‘Hyperbright’ types) have a sharply focused output in which the light intensity falls off very sharply beyond the specified viewing angle.
LEDs are available in five different ‘brightness’ categories, which are usually known as Standard, High Brightness, Super Bright, Ultrabright, and Hyperbright. The brightness level is usually specified in milli-candelas (mcd), with the LED passing an operating current of 20mA. The table in Figure 4 presents typical optical output-power and viewing-angle figures for the five types of 5mm round LED. Note in the ‘red’ LED column that the Ultrabright and Hyperbright devices (which use water-clear lenses) are 143 and 500 times brighter, respectively, than a standard red LED.
LED Type | Viewing Angle | Red | Green | Orange |
---|---|---|---|---|
Standard | 60° | 7mcd | 5.2mcd | 8mcd |
High Brightness | 40° | 30mcd | 25mcd | 50mcd |
Super Bright | 30° | 125mcd | 120mcd | 140mcd |
Ultrabright | 25° | 1000mcd | -- | -- |
Hyperbright | 25° | 3500mcd | -- | -- |
FIGURE 4. Typical optical output power figures — in millicandelas — of five basic types of 5mm round red, yellow, and green LEDs.
In use, an LED must be wired in series with a current-limiting device such as a resistor. Figure 5 shows how to work out the resistance (R) value needed to give a particular current from a particular DC supply voltage. Thus, if a red LED is required to operate at 20mA from a 10V supply, R needs a value of (10V - 2V)/0.02A = 400R. In practice, R can be connected to either the anode or the cathode of the LED.
FIGURE 5. Method of finding the R value for a given VS and If.
A LED can be used as an indicator in an AC circuit by wiring it in inverse parallel with a IN4148 (or similar) silicon diode, as shown in Figure 6, to prevent the LED from being reverse-biased; the LED is fed with a half-wave current in this mode, so — for a given brightness — the ‘R’ value must be halved relative to that indicated in the Figure 5 DC circuit.
FIGURE 6. Using an LED as an indicator in an AC circuit.
SPECIAL-PURPOSE LEDs
LEDs are readily available in a variety of special-purpose forms, the best known of which are the ‘direct connection’ type, the ‘flasher’ type, and the multicolor types.
Direct connection LEDs are designed to be connected directly across a fixed-value DC or AC voltage source. DC voltage types take the basic form shown in Figure 7(a) and incorporate a current-limiting resistor that is housed in the LED body in 5V and 12V types, or in one of the LED leads in higher voltage types. AC voltage types (usually designed for use with 110V or 240V supplies) take the basic form shown in Figure 6, but are usually housed in an insulated panel-mounting assembly.
FIGURE 7. Basic form of a direct connection DC LED (a) and a flasher LED (b).
Flashing LEDs take the basic form shown in Figure 7(b) and have a built-in integrated circuit that gives the flashing effect. They are available in red, green, and yellow, have a typical flashing frequency of 2Hz, and can (typically) use 6V to 12V DC supplies.
Multicolor LEDs are actually two-LED devices. Figure 8 shows a ‘bi-color’ device that comprises a red and a green LED connected in inverse parallel, so that the color green is generated when the device is connected in one polarity, and red is generated when it is connected in the reverse polarity. This device is useful as a polarity or null indicator.
FIGURE 8. Bi-color LED actually houses two LEDs connected in inverse parallel.
Figure 9 shows another type of multicolor LED, which is sometimes known as a ‘tri-color’ type. This comprises a green and red LED mounted in a three-pin common-cathode package. This device can generate green or red colors by turning on only one LED at a time, yellow by turning both LEDs on by equal amounts, or any color between green and red by turning both LEDs on in the appropriate ratios.
FIGURE 9. Multicolor LED, giving three colors from two junctions.
MULTI-LED CIRCUITS
If several LEDs need to be driven from a single power source, this can be done by wiring all LEDs in series, as shown in Figure 10, provided that the supply voltage is significantly greater than the sum of the individual LED forward voltages.
FIGURE 10. LEDs wired in series and driven via a single current-limiting resistor.
This circuit thus consumes a minimum total current, but is limited in the number of LEDs that it can drive. Any number of these basic circuits can, however, be wired in parallel, so that any number of LEDs can be driven from a single source, as shown in the six-LED circuit in Figure 11.
FIGURE 11. Any number of Figure 10 circuits can be wired in parallel, to drive any number of LEDs.
An alternative way of simultaneously powering several LEDs is to simply wire a number of the Figure 5 circuits in parallel, as shown in Figure 12. Note, however, that this circuit is very wasteful of supply current (which equals the sum of the individual LED currents).
FIGURE 12. This circuit can drive any number of LEDs, but at the expense of high current.
Figure 13 shows a “what not to do” LED-driving circuit, in which all the LEDs are wired directly in parallel. Often, this circuit will not work correctly because inevitable differences in the forward characteristics of the LEDs cause one LED to hog most or all of the available current, leaving little or none for the remaining LEDs.
FIGURE 13. This LED-driving circuit may not work; one LED may hog most of the current.
LED FLASHER CIRCUITS
SIMPLE DESIGNS
One of the simplest types of LED display circuit is the LED flasher in which a single LED repeatedly switches on and off, usually at a rate of one or two flashes per second. A two-LED flasher is a simple modification of this circuit, but is arranged so that one LED switches on when the other switches off, or vice versa.
Figure 14 shows the practical circuit of a transistor two-LED flasher, which can be converted to single-LED operation by simply replacing the unwanted LED with a short circuit.
FIGURE 14. Transistor two-LED flasher circuit operates at about 1Hz.
Here, Q1 and Q2 are wired as a simple 1Hz astable multivibrator, in which Q1 and LED1 turn on as Q2 and LED2 turn off, and vice versa, and in which the astable switching rates are controlled by the values of C1-R3 and C2-R4.
Figure 15 shows an IC version of the two-LED flasher, based on a 555 or 7555 timer IC that is wired in the astable mode, with its main time constants determined by the C1 and R4 values and giving a cycling rate of about 1Hz (one flash per second). The circuit action is such that output pin 3 of the IC alternately switches between the ground and the positive supply voltage levels, alternately pulling LED1 on via R1 or driving LED2 on via R2. The circuit can be converted to single-LED operation by omitting LED2 and R2.
FIGURE 15. IC two-LED flasher circuit operates at about 1Hz.
Figure 16 shows a useful modification of the above circuit, in which the flashing rate is made variable via RV1, and two pairs of series-connected LEDs are connected in the form of a cross so that the visual display alternately switches between a horizontal bar (LED1 and LED2 ON) and a vertical bar (LED3 and LED4 ON), thus forming a visually interesting display. The cycling rate is variable from 0.3 to 3 flashes per second.
FIGURE 16. The rate of this four-LED double-bar flasher is variable from 3 to 0.3 flashes per second.
MICROPOWER LED FLASHERS
Simple LED flasher circuits of the types shown in Figures 14 to 16 consume mean operating currents of several milliamps. Micropower LED flashers, on the other hand, consume mean operating currents that are measured in microamps (typically ranging from 2µA to 150µA), and are intended mainly for use in battery-powered ‘emergency indicator,’ ‘battery state,’ and ‘burglar deterrent’ applications.
In emergency indicator applications, micropower LED flashers can be used to indicate the positions of emergency exits, lanterns, torches, alarm buttons, or safety equipment, etc., under dark conditions (perhaps caused by a failure of a main lighting system). When used as battery state indicators, they are often fitted in smoke alarms and other low-current long-life units that are powered by 4.5V to 12V batteries. When used as burglar deterrents, they are prominently fitted to real or dummy burglar alarm control or alarm/siren boxes or CCTV cameras, etc.
To understand the basic principles behind micropower LED flashers, you must first learn some basic facts concerning visual perception, as follows.
- The human eye/brain combination is sharply attracted by sudden changes in visual patterns or light levels; it is particularly sensitive to some types of flashing light. Figure 17 shows the typical ‘light flash’ response of the human eye/brain combination when presented with a bright LED-generated pulse of light.
- Note from Figure 17 that the flash must be present for at least 10mS to be seen (perceived) at full brilliance, and that — when the flash terminates — the ‘persistence of vision’ effect causes the perceived brilliance to decay fairly slowly, typically taking 20mS to fall to 50% of its maximum (pre-switch off) value. Consequently, the eye can only see flashing lights as individual flashes if they are separated by a period of at least 20mS; if they are separated by less than 20mS, they are seen (because of the ‘persistence of vision’ effect) as a continuous light.
- Also note from Figure 17 that — if the flashes are separated by at least 20mS — the brain ‘sees’ the individual flashes at full brilliance if they have a duration of 10mS or greater, but sees them at diminishing brilliance at durations below 10mS (a 2mS flash appears at roughly 1/5th of true brilliance; the perceived brilliance falls off rapidly at durations below 1mS). The perceived duration of a 20mS flash (30mS) is only 50% greater than that of a 10mS flash (20mS).
- The human eye/brain combination is very sharply attracted by flashing lights that have repetition periods in the approximate range 0.5 to 5 seconds, but is less attracted by flashing lights that have repetition periods above or below this range.
- Modern low-cost Super Bright LEDs, when generating a 10mS or longer light pulse, produce a brightness level that is adequately eye-catching for most practical purposes when pulsed by a 2mA current.
FIGURE 17. Typical ‘light flash’ response of the human eye/brain combination. Doom 2019 rip and tear.
When the above sets of facts are put together, it transpires that the ‘ideal’ micropower LED flasher — when using a Super Bright LED — should produce a pulse with a duration (d) of 10mS at a current (I) of 2mA, at a repetition period (p) of 2 seconds (= 2000mS). Note that, under these conditions, the mean current (Imean) of the LED is given by
Imean = I x d/p
and is a mere 10µA in this particular example (at a 30 second repetition period, Imean is a minute 0.67µA).
In practice, the actual mean current consumed by a micropower LED flasher circuit is equal to the sum of the LED and the driver currents, and is inevitably higher than the minimum figure indicated above. Figures 18 and 19, for example, show two alternative micropower LED flasher circuits that — when powered from 6V supplies — consume total currents of 86µA and 12µA, respectively.
The Figure 18 circuit is designed around a CMOS 7555 ‘timer’ IC that is used in the astable mode and typically consumes an unloaded operating current of 75µA at 6V. In this mode, C1 alternately charges up via R1-R2 and discharges via R2 only, thus generating a highly asymmetrical output waveform on pin 3, which pulls the LED on via current-limiting resistor R3 during the brief ‘discharge’ part of each operating cycle.
FIGURE 18. Circuit and performance details of a 7555-based micropower LED flasher unit.
The Figure 18 table summarizes the circuit’s performance details when optimized for operation at various spot voltages in the range 3V to 12V.
The Figure 19 circuit is designed around a CMOS 4007UB IC, which contains two complementary MOSFET transistor pairs plus one CMOS inverter, all housed in a 14-pin DIL package.
FIGURE 19. This 4007UB-based micropower LED flasher circuit consumes a mean current of 12µA at 6V.
In this application, the IC is wired as a micropower ring-of-three asymmetrical astable multivibrator which — when powered from a 6V supply — drives the LED on for 10mS at two-second repetition intervals; the ON time is controlled by C1-R1, the OFF time by C1-R2, and the LED current (2mA nominal) is controlled by R4. The circuit consumes an unloaded operating current of 2µA, and a loaded current (when driving the LED with 2mA pulses) of 12µA.
Note that the basic circuit of Figure 19 can be used at any supply voltages in the range 4.5V to 12V, but that the actual component values must be selected to suit the specific supply voltage used. Also note that — at supply voltages of 6V or greater — the circuit can drive two or more series-connected LEDs without increasing the total current consumption, provided that R4’s value is altered to set the LED ON currents at 2mA.
The table in Figure 20 shows the nominal life expectancies of various types of alkaline cell/battery when continuously driving various types of micropower LED flasher circuits.
12µA Load | 86µA Load | 320µA Load | |||||
Alkaline cell/battery type | Capacity (per cell or battery) | Monthly capacity drain & predicted cell/battery life | |||||
Drain | Life | Drain | Life | Drain | Life | ||
AAA | 1 Ah | 0.88% | 3.3 Yrs | 6.28% | 1.0 Yrs | 23.4% | 0.3 Yrs |
AA (1.5V) | 2 Ah | 0.44% | 4.0 Yrs | 3.14% | 1.7 Yrs | 11.7% | 0.6 Yrs |
C (1.5V) | 6.5 Ah | 0.135% | 4.6 Yrs | 0.97% | 3.2 Yrs | 3.6% | 1.6 Yrs |
D (1.5V) | 13 Ah | 0.07% | 4.8 Yrs | 0.48% | 3.9 Yrs | 1.8% | 2.4 Yrs |
PP3 (9V) | 0.55 Ah | 1.59% | 2.6 Yrs | 11.4% | 0.6 Yrs | 42.5% | 0.2 Yrs |
FIGURE 20. Table showing the life expectancies of various types of alkaline cell/battery when driving micropower LED flasher circuits.
The data relates to the circuits in Figure 18 (drawing 86µA at 6V), and Figure 19 (drawing 12µA at 6V), and to the once-popular but now obsolete LM3909 ‘LED flasher’ IC (withdrawn from production by National Semiconductor), which draws a minimum operating current of 320µA.
Note in Figure 20 that the ‘predicted cell/battery life’ figures relate to cells/batteries that have initial (unused) life expectancies of five years, i.e., in which their charges leak away at a steady rate of 1.67% per month. The total in-use monthly capacity drain equals the sum of the leakage and the loading drain figures, and forms the basis of the life prediction figures shown in the table.
LOW-VOLTAGE MICROPOWER LED FLASHERS
The basic micropower LED flasher circuit in Figure 19 can — if its component values are suitably selected — be reliably used at an absolute minimum supply voltage of 4.5V. If you have an application where you need to drive this basic flasher circuit from a 3V battery, you can do so by using the 3V battery to directly drive a super-efficient voltage-doubler circuit based on the popular ICL7660 IC, and use the 6V output of the doubler (connected directly across C2 in Figure 19) to power the 6V version of the Figure 19 circuit which, in this case, will consume a mean current of 24µA from the 3V battery.
Alternatively, if you need to drive the basic flasher circuit from a 1.5V cell, you can do so by using the cell to drive a cascaded pair of ICL7660 voltage-doubler circuits, and use their 6V output (connected directly across C2 in Figure 19) to power the 6V version of the Figure 19 circuit which, in this case, will consume a mean current of 48µA from the 1.5V cell. NV
1.5 Volt LED Flashers #1: four circuits with description
1.5v LED FLASHER: This is a very basic little circuit built around the LM3909 IC. A list of components and values is included.
10 Channel LED Sequencer: based on4017
10 LED Sequencer: in PDF format, text in Finnish
16 Stage Bi-Directional LED Sequencer:
2 LED Flasher: simple2- transistor circuit which blinks2- LEDs
2 Transistor LED Flasher #1:
2 Transistor LED Flasher #2:
28 LED Clock Timer 72 LED Clock: programmable clock Timer circuit that uses individual LEDs to indicate hours and minutes
High Intensity Leds
3 Way Blinking LEDs:
40 LED Bicycle Light (555 Timer 6 Volt):
7 Segment LED Counter:
72 LED Clock:
9 Second Digital Readout Timer #2:
9 Second LED Relay Timer #2:
AC Line Powered LEDs:
Adjustable Flashing Led:
Alternating LED Blinker uses Four Parts: 03/26/98 EDN-Design Ideas /Grand Prize Winner1998
Sep 3, 2014 - Multi-cursor in Visual Studio. If the lines are consecutive select the location in the first line and then use Shift-Alt and the up and down arrow keys to select multiple lines. Visual studio multiple cursors.
Alternating LED Flasher uses Minimal Parts: 11/20/97 EDN-Design Ideas / A pair of alternating flashing LEDs makes an excellent visual alarm, this alternating LED flasher is based on one LED with built-in flashing function and two transistors driving the other normal LED
Alternating LEDs Flasher: Mar-03
Analog LED Bar VU Meter: built around discrete components
Astable Multivibrator 1:
AT89C2051 / 4051 Driving Dot LED:
Audio LED VU Meter: built around discrete components
Back & Forth Flasher: for16 LEDs
Basic LM3909 LED Flasher: runs from1.5-Volt battery
Bicycle Back Safety Light: Flashing13 LED unit,3V supply Also suitable for jogger/walkers
Bicycle Safety Lights:
Big LED Clock:
Buck IC boosts battery voltage for white LED: 04/24/03 EDN-Design Ideas / White-light LEDs are finding their way into many markets that incandescent bulbs once served. Flashlights are among the newer applications in which reliability, ruggedness, and ability to control the power draw of the LEDs make these devices attractive. With incandescent bulbs, the power management for the device is a simple on-off switch.
Car Message Display: CaMeD was designed and built to be used in an automobile. Its purpose is to display various symbols/messages to the car driver traveling behind you. It uses1024 LEDs to form a32 x32 matrix display. A total of12 symbols/messages can be displayed,4 of them being user-definable by using a visual basic utility tool connected to the rs232 port of a PC.
Circuit Controls Two LEDs With One Microcontroller Port Pin : 04/01/02 Electronic Design - Ideas for Design / Microcontroller port pins can typically be driven either high or low, or else be put into an 'input' or high-impedance state. This circuit uses the three states to drive two separate LEDs with one port pin.
Circuit drives mixed types and quantities of LEDs: 10/03/2002 EDN - Design Ideas / Portable systems often use LEDs of different colors and in varying quantities of each color. Some examples are white for the display backlight, green for keypad illumination, and red for power. Typically, the LEDs derive power from at least two power supplies: one for 'standard' LEDs (red and green) and one for white LEDs.
Circuit efficiently switches bipolar LED: 11/22/2001 EDN - Design Ideas / The circuit in Figure 1 represents one method to switch a bipolar, two-color LED using an SPDT mechanical switch or relay. This circuit wastes power and does not work properly if the power-supply voltage is not substantially more than the sum of the LEDs' forward voltages.
Connecting LED to PIC Micro I/O Pins:
Constant Current White LED Flashlight:
Create secondary colors from multicolored LEDs: 07/24/03 EDN-Design Ideas / It is well-known that simultaneously mixing two primary-color light sources, such as red and green, creates a secondary color, such as yellow. This mixing process commonly occurs in tricolor LEDs.
Dancing LEDs: A LED sequencer, following the rhythm of music or speech 9 Volt Battery-operated portable unit
Diode & LED Tester:
Dual Alternating Flashing Light:
Dual Tandem Flashing Light:
DualGate Inverter Oscillator Saves Power, Boosts LED Brightness: 06/24/02 Electronic Design - Ideas for Design / An LED's brightness is directly proportional to the current through it, which creates a challenge for low-voltage and battery-powered applications.
Economical Circuit Drives White LEDs: 11/23/00 EDN-Design Ideas / PDF contains multiple circuits - scroll to find this circuit.
Expandable 16 Stage LED Sequencer:
Fading Red Eyes: can be used to slowly illuminate and fade a pair of red LEDs
Fantastic Atom Expander: 'exploding atom' effect using 98 LEDs
Fire Lights: LEDs shimmer randomly as though on fire. Circuit generates true random coin-toss output.
Flasher Circuit : LED Flasher, suitable for Christmas Lights
Flashing Christmas LED Display:
Flashing High Intensity LED 3rd Brake Light: This circuit to make a flashing3rd brake light assembly was designed to be easy to locate all the needed components and reasonably in expensive to build.
Get More than Three Colors From a Dot Matrix LED : 06/04/98 EDN-Design Ideas
Grantronics Projects Christmas Tree : flashes LEDs mounted to Christmas tree shape PCB, kit from kitsrus.com
Holiday Map Display:
ICL7660 LED Flasher:
Inexpensive LED Drives Flash & Beep Circuit: 06/05/97 EDN-Design Ideas
Infrared LED Illuminator:
LED Amplifier:
LED Bar VU Meter:
LED Barograph Drive:
LED Chaser: simple10 LED chaser
LED Christmas lights :
LED doubles as emitter and detector: 08/16/2001 EDN - Design Ideas / Every junction diode exhibits some degree of photosensitivity when it receives light comprising an appropriate range of wavelengths. The spectral response of a junction diode depends on a variety of factors, including material chemistry, junction depth, and packaging.
LED driver combines high speed, precision : 08/21/03 EDN-Design Ideas / Applications such as turbidity measurement and densitometry require cleanly pulsed light sources with stable amplitudes. The LED driver in Figure 1 illuminates retinal neurons in a biological experiment that has similar requirements.
LED driver delivers constant luminosity: 06/12/03 EDN-Design Ideas / The circuit in Figure 1 is similar in principle to that of a previous Design Idea (Reference 1) but offers improved, more reproducible performance. The output current is almost constant over an input-voltage range of 1.2 to 1.5V and is insensitive to variations of transistor gain. Transistors Q1 and Q2 form an astable flip-flop.
LED Driver Displays Standing Wave Radio: 03/18/99 EDN-Design Ideas / PDF contains multiple circuits - scroll to find this circuit
LED Flasher & TRAC Pulser Work off AC Line: 01/15/98 EDN-Design Ideas
LED Flasher indicates Low Battery Condition: 01/02/97 EDN Design Ideas
LED Flasher, Two Transistor:
LED Flasher: built using two transistors and some other components
LED flasher-a :
LED flasher-b:
LED Light Dimmers uses only Two Lines: 03/21/02 EDN-Design Ideas / PDF contains multiple circuits - scroll to find the one of interest -- This circuit provides32 steps of brightness control (from0 to100%) for a backlight or instrument panel, using just two general-purpose-microprocessor signals. Although the circuit shows the circuit driving white LEDs, the load could also be a dc motor or an incandescent lamp. The basis of the circuit is a modified Schmitt-trigger relaxation oscillator controlled by MAX5160 digital potentiometer.
LED Mood Light: this LED circuit makes a nice lamp that is low power, runs cool, and has a long lifetime, operates from12V, puts out a warm yellow shade of light, the color may be adjusted by changing the number of red or green LED strings
LED or Lamp Flasher : Minimum parts counting. Designed for3V battery operation
LED or Lamp Pulser : Astonishing effect4.5 Volt supply
LED Pilot Light (AC or DC): LED current is constant between 6 and 8 mA at5 to30Vdc
LED Pulser With Audible Output:
LED Sign: uses two LED arrays to form a 7 X 10 matrix. It produces moving messages or animations stored in an EPROM.
LED Stroboscope: This simple LED Stroboscope circuit which I designed, maintains constant
brightness of the LED at all frequencies. This is accomplished by duty-cycle and pulse width control. It is useful for measuring the speed of motors. It can easily be calibrated using a watch so you don’t need a frequency counter.
brightness of the LED at all frequencies. This is accomplished by duty-cycle and pulse width control. It is useful for measuring the speed of motors. It can easily be calibrated using a watch so you don’t need a frequency counter.
LED Torch : A white LED torch that consumes just24 mW
LED7 Solar Tracker:
LEDs Flasher, Alternately: Classic astable multivibrator using2 transistors. Transistor is not critical. Try these:2N4401,2N2222, NTE123A, NTE123AP, NTE159, TUP/TUN and those in your junk box, you may find that most of them will work.
Light a white LED from half a cell: 06/12/03 EDN-Design Ideas / Whether you use them as indicators or to provide illumination, LEDs are hard to beat in efficiency, reliability, and cost. White LEDs are rapidly gaining popularity as sources of illumination, as in LCD backlights, but with forward voltages typically ranging from 3 to 5V, operating them from a single cell presents obvious difficulties.
Light Pollution Meter: LED brightness control circuit and a multimeter to compare light levels to LED level.
Linear Constant Current LED Lamp Dimmer: This circuits drives24 white light LEDs with an adjustable constant current.
Low Power LED Flasher : based on LM3909
Mains Operated Christmas Star:
McMurtrie's Self Powered Flashing LED : circuit which uses a LED as solar panel to charge a capacitor which flashes a LED, the LED will blink when the circuit is placed in bright light
Park Aid: 3-LEDs signal bumper-barrier distance Infrared operation, indoor use
PIC Micro LED Projects:
PIC16F84 LED Chaser:
Picxie 2 8x8 Animated LED Signboard:
Propeller Clock: a few light emitting diodes spin, precisely controlled by a PIC microprocessor, giving the illusion of a larger array.
Remote Solar LED Light:
Reset Circuit Provides Snappy Action: 04/29/99 EDN-Design Ideas / PDF contains multiple circuits - scroll to find this circuit
Rugged LED Brake Lights :
Serial Comms to LED Driver:
Seven Component Regulated LED Lamp :
Signal Processor Adds LED Display: 06/05/96 EDN-Design Ideas
Simple Logic Probe uses Bicolor LED: 03/13/98 EDN-Design Ideas
Single cell lights any LED: 07/05/2001 EDN - Design Ideas / The circuit in Figure 1 allows you to light any type of LED from a single cell whose voltage ranges from 1 to 1.5V. This range accommodates alkaline, carbon-zinc, NiCd, or NiMH single cells. The circuit's principal application is in LED-based flashlights, such as a red LED in an astronomer's flashlight, which doesn't interfere with night vision.
Single FET Controls 2nd LED Array in SwitchMode LED Backlight: Maxim APP1871: Feb03,2003 / A design in which the display is backlit (or frontlit) for extended periods needs an efficient circuit that drives the LEDs with a controlled current, and eliminates the wasted power associated with current-limiting resistors. A switch-mode boost design that regulates current instead of voltage accomplishes this purpose.
Single FET Controls LED Array: 04/12/01 EDN-Design Ideas / PDF contains multiple circuits - scroll to find this circuit.
Single LED indicates Two Power States: 12/05/96 EDN-Design Ideas / Uses a single bicolor LED to indicate both power-on and blown-fuse conditions
Solar Charged LED Flashlight:
Special Lighting : experiments with white LEDs
Telephone In Use LED Indicator:
Telephone in use Light:
Three Way Blinking LEDs :
Two LED Flasher: simple2- transistor circuit which blinks2- LEDs
Two LEDs Perform Rudimentary Spectral Analysis: 09/01/94 EDN-Design Ideas
Two Signals Easily Control Tricolor LED: 09/14/95 EDN-Design Ideas
Two Transistor LED Flasher #1:
Two Transistor LED Flasher #2:
Voltage to current converter drives white LEDs: 06/27/2002 EDN - Design Ideas / You sometimes need to drive a white LED from one 1.5V battery. Unfortunately, the forward voltage of a white LED is 3 to 4V. So, you would need a dc/dc converter to drive the LED from one battery. Using the simple circuit in Figure 1, you can drive one white LED or two series-connected green LEDs, using only a few components.
White LED drive from 1.5V: Blocking oscillator based design allows LED + power supply to fit in #222 lamp base.
White LED driver touts high efficiency: 06/12/03 EDN-Design Ideas / White LEDs, the most recent addition to the LCD backlight, find common use in providing backlight for color LCDs. Thanks to their size and white-light output, they appear in small, portable devices with color displays, such as PDAs and cellular phones. Like other LEDs, a white LED needs a constant-current source—typically, on the order of 15 to 20 mA.
White LED Flashlight: